A cartridge reaches the console through an edge connector. The Famicom has 60 pins at 2.54 mm pitch (0.1 inch). The NES has 72 pins at 2.50 mm pitch, which is not 0.1 inch, so ordinary female board edge connectors do not fit. Directions below are from the console’s viewpoint, so “in” (the arrow towards the console) is a signal the cartridge drives, and “out” is a signal the console drives to the cartridge.
60-pin Famicom connector
Seen looking into the connector. Pins 01 to 30 are on the label side of the cartridge, left to right.
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 01 | GND | 31 | CartridgePresent or 5 V supply (see note) |
| 02 | CPU A11 (out) | 32 | M2 (out) |
| 03 | CPU A10 (out) | 33 | CPU A12 (out) |
| 04 | CPU A9 (out) | 34 | CPU A13 (out) |
| 05 | CPU A8 (out) | 35 | CPU A14 (out) |
| 06 | CPU A7 (out) | 36 | CPU D7 (both) |
| 07 | CPU A6 (out) | 37 | CPU D6 (both) |
| 08 | CPU A5 (out) | 38 | CPU D5 (both) |
| 09 | CPU A4 (out) | 39 | CPU D4 (both) |
| 10 | CPU A3 (out) | 40 | CPU D3 (both) |
| 11 | CPU A2 (out) | 41 | CPU D2 (both) |
| 12 | CPU A1 (out) | 42 | CPU D1 (both) |
| 13 | CPU A0 (out) | 43 | CPU D0 (both) |
| 14 | CPU R/W (out) | 44 | /ROMSEL (/A15 + /M2) (out) |
| 15 | /IRQ (in) | 45 | Audio from the 2A03 (out) |
| 16 | GND | 46 | Audio to RF (in) |
| 17 | PPU /RD (out) | 47 | PPU /WR (out) |
| 18 | CIRAM A10 (in) | 48 | CIRAM /CE (in) |
| 19 | PPU A6 (out) | 49 | PPU /A13 (out) |
| 20 | PPU A5 (out) | 50 | PPU A7 (out) |
| 21 | PPU A4 (out) | 51 | PPU A8 (out) |
| 22 | PPU A3 (out) | 52 | PPU A9 (out) |
| 23 | PPU A2 (out) | 53 | PPU A10 (out) |
| 24 | PPU A1 (out) | 54 | PPU A11 (out) |
| 25 | PPU A0 (out) | 55 | PPU A12 (out) |
| 26 | PPU D0 (both) | 56 | PPU A13 (out) |
| 27 | PPU D1 (both) | 57 | PPU D7 (both) |
| 28 | PPU D2 (both) | 58 | PPU D6 (both) |
| 29 | PPU D3 (both) | 59 | PPU D5 (both) |
| 30 | +5 V | 60 | PPU D4 (both) |
Directions follow the arrows of the wiki’s diagram, read from the console’s viewpoint: “out” is driven by the console, “in” by the cartridge, “both” is bidirectional. Pin 31: on some revisions of the RF modulator board, pin 31 connects only to the TV/game switch there, so the RF modulator can send video only if a cartridge connects pin 30 to pin 31. On other revisions pin 31 is on the normal 5 V supply.
72-pin NES connector
On a front-loader, pins 01 to 36 are the top side of the connector, and pins 36 to 01 are on the label side of the cartridge, left to right. PPU A10 and PPU A11 (pins 63 and 62) are in reverse order on the NES, not sequential.
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 01 | GND | 37 | SYSTEM CLK |
| 02 | CPU A11 | 38 | M2 |
| 03 | CPU A10 | 39 | CPU A12 |
| 04 | CPU A9 | 40 | CPU A13 |
| 05 | CPU A8 | 41 | CPU A14 |
| 06 | CPU A7 | 42 | CPU D7 |
| 07 | CPU A6 | 43 | CPU D6 |
| 08 | CPU A5 | 44 | CPU D5 |
| 09 | CPU A4 | 45 | CPU D4 |
| 10 | CPU A3 | 46 | CPU D3 |
| 11 | CPU A2 | 47 | CPU D2 |
| 12 | CPU A1 | 48 | CPU D1 |
| 13 | CPU A0 | 49 | CPU D0 |
| 14 | CPU R/W | 50 | /ROMSEL (/A15 + /M2) |
| 15 | /IRQ (in) | 51 | EXP 9 |
| 16 | EXP 0 | 52 | EXP 8 |
| 17 | EXP 1 | 53 | EXP 7 |
| 18 | EXP 2 | 54 | EXP 6 |
| 19 | EXP 3 | 55 | EXP 5 |
| 20 | EXP 4 | 56 | PPU /WR |
| 21 | PPU /RD | 57 | CIRAM /CE (in) |
| 22 | CIRAM A10 (in) | 58 | PPU /A13 |
| 23 | PPU A6 | 59 | PPU A7 |
| 24 | PPU A5 | 60 | PPU A8 |
| 25 | PPU A4 | 61 | PPU A9 |
| 26 | PPU A3 | 62 | PPU A11 |
| 27 | PPU A2 | 63 | PPU A10 |
| 28 | PPU A1 | 64 | PPU A12 |
| 29 | PPU A0 | 65 | PPU A13 |
| 30 | PPU D0 | 66 | PPU D7 |
| 31 | PPU D1 | 67 | PPU D6 |
| 32 | PPU D2 | 68 | PPU D5 |
| 33 | PPU D3 | 69 | PPU D4 |
| 34 | CIC to pak (CIC data out of the console) | 70 | CIC +RST |
| 35 | CIC to MB (CIC data towards the console) | 71 | CIC CLK |
| 36 | +5 V | 72 | GND |
As on the Famicom, the CPU and PPU address pins, R/W, M2, /ROMSEL, PPU /RD, PPU /WR, PPU /A13, SYSTEM CLK, CIC +RST and CIC CLK are driven by the console, and the data pins go both ways. /IRQ, CIRAM A10, CIRAM /CE and CIC to MB (pin 35) are driven by the cartridge. The CIC to pak signal (pin 34) is driven by the console. The EXP pins have no direction in the wiki’s diagram.
Comparison
| Pins | 60-pin Famicom | 72-pin NES |
|---|---|---|
| +5 V, GND | yes | yes |
| CPU A0–A14, D0–D7, R/W, M2, /ROMSEL, /IRQ | yes | yes |
| PPU A0–A13, D0–D7, /RD, /WR, /A13 | yes | yes |
| CIRAM A10, /CE | yes | yes |
| Audio in and out | yes | no |
| CartridgePresent | yes | no |
| CIC pins | no | yes |
| EXP 0–9 | no | yes |
| SYSTEM CLK | no | yes |
- Famicom cartridges usually have most chips on the side of the board opposite the label (Nintendo boards do; third-party boards vary). On the NES most chips are on the label side.
- A slash before a name marks an active-low signal.
- The NES connector is mostly a mirror image of the Famicom’s. Most Nintendo cartridge boards are numbered as in these tables.
Signals
- +5V: 5 V from the main regulator. GND: 0 V.
- SYSTEM CLK: the main oscillator output, only on the 72-pin connector; about 21 MHz on NTSC and 27 MHz on PAL machines.
- M2 (PHI2, φ2 in official documents): the CPU clock output. The address bus and R/W are valid while M2 is high (essentially the whole high time). Data is guaranteed or required valid only on the falling edge of M2, for reads and writes. Timeline: M2 rises; address and R/W become valid before it; read data arrives just before the fall; write data is valid for the second half.
- CPU R/W: high for reads, low for writes; changes only while M2 is low.
- CPU A0–A14: the CPU address bus, stable while M2 is high. A15 exists but is not on the connector.
/ROMSELis given instead. - CPU D0–D7: the bidirectional CPU data bus. It goes high impedance on reads so external memory can drive it.
- /ROMSEL: NAND of M2 and CPU A15. It is low when the CPU reads or writes
$8000–$FFFFand the address is stable, so it can enable ROM chips directly. Advanced mappers add logic between this pin and the PRG chip enable (for example to avoid bus conflicts). It is the only way to know the state of A15, so any mapper that decodes addresses needs it. - /IRQ: interrupt request input; pull low to interrupt the CPU. The console has an internal pull-up, so it can float if unused. NES hardware can safely drive it high or low (the cartridge is the only outside source), but PlayChoice-10 modules must treat it as an open-collector input.
- Audio from 2A03: the 2A03 audio output, already amplified; only on 60-pin connectors. Audio to RF: usually tied to the previous; it goes straight to the console’s sound output, which lets a cartridge mix its own audio. Not on 72-pin connectors.
- EXP0–EXP9: connect to the expansion port under the NES-001 and have no fixed meaning. EXP6 became the standard for expansion audio.
- PPU /WR (“/WE” in official documents): low while the PPU writes; address and data are stable on the falling edge. PPU /RD (“/RD”): low while the PPU reads; the address is stable on the falling edge and data should be stable until the rising edge.
- PPU A0–A13 (“PA0–13”): the PPU address bus. Most boards tie PPU A13 straight to the chip enable of CHR ROM or RAM, so it sits at
$0000–$1FFFwith no more logic. - PPU D0–D7 (“PD0–7”): the bidirectional PPU data bus; high impedance when PPU /RD goes low so memories can drive it.
- PPU /A13: inverted A13, normally used to map nametables and attribute tables to
$2000–$3FFF. - CIRAM /CE (VRAM /CS): enables the console’s internal 2 KiB VRAM. Usually wired straight to PPU /A13; boards with their own nametable RAM add their own logic.
- CIRAM A10 (VRAM A10): selects the 1 KiB bank of the internal VRAM, which sets the nametable arrangement. Connect it to PPU A10 for horizontal arrangement (vertical mirroring) or PPU A11 for vertical arrangement (horizontal mirroring). See nametable mirroring.
- CIC +RST and CIC CLK: on the top-loading NES-101 these are connected to +5 V and PPU D4; the other two CIC pins float. See CIC lockout.
Sources
The NESdev Wiki text is available under CC BY-SA 3.0. This page is written in our own words from the raw wikitext kept in samples/nes/sources/hardware. The wiki’s diagrams show arrows for each pin; this page lists them as tables. The bidirectional marks on the data pins come from those arrows.