The front-loading NES contains a CIC lockout chip, a microcontroller that performs a proprietary handshake. It was an anticompetitive measure. The Famicom and the top-loading NES do not have it. CIC stands for “Checking Integrated Circuit” in Nintendo’s patents. The pins on the cartridge connector are on cartridge connectors. This page describes the handshake at the level of the wiki and gives the chip’s pinout and registers; it does not give the chip’s program or the key stream.
Lock and key
- The chip in the console and the chip in the cartridge are the same IC. The one in the NES acts as the lock, the one in the cartridge as the key. They differ only in how they are wired.
- The output of each chip goes to the input of the other. The LOCK/KEY pin is pulled to +5 V in the NES and grounded on the cartridge. Both share the same 4 MHz clock on pin 6.
- The key’s RESET pin is connected to SLAVE CIC RESET on the lock. The lock’s RESET pin is on the system reset bus. You can see this by inserting a game while the system is on: the NES will not work until you press reset, which resets the lock, which in turn resets the key.
- /CPU & PPU RESET is not connected on the key. On the lock it is connected to the CPU and PPU reset pins.
- Pins 11 to 15 are grounded on both chips in an NES; they are used in multi-game systems so several CICs can be addressed in one system. VCC goes to +5 V.
- After power-on or reset, the lock sends the reset and initialisation signals to the key. The key must return the correct response. If it does not, the lock pulls /CPU & PPU RESET low with a 1 Hz square wave, so the console keeps resetting. Because they share a clock and the lock can reset the key, the two stay in step.
Regions
One purpose of the CIC was to tie consoles and games to their sales regions, to fight imports. That mattered in the PAL and Asian regions, where third parties such as Mattel, ASD and Bandai distributed the NES before Nintendo subsidiaries existed. The CIC codes on 72-pin cartridges (the Famicom Network System has CICs but not 72-pin connectors):
| CIC code | Region |
|---|---|
| 3193 | NTSC |
| 6113 | NTSC |
| 3197 | PAL-A |
| 3195 | PAL-B |
| 3196 | Asia |
| 3198 | FamicomBox |
Finding a cartridge’s CIC region
- Read the front label. If it has an ID code (for example
NES-SM-USAfor the US Super Mario Bros.) or just a region code, look it up in the table below. Some PAL games say PAL-A or PAL-B on the label. FamicomBox cartridges have yellow labels with no ID code and are upside down compared with standard cartridges. - If there is no ID code (early first-party releases), check the back label, box or manual.
- Otherwise open the cartridge with the right screwdriver and read the CIC.
| Region code | Meaning | CIC region |
|---|---|---|
| USA | United States of America | NTSC |
| CAN | Canada | NTSC |
| AUS | Australia | PAL-A |
| GBR | Great Britain | PAL-A |
| ITA | Italy | PAL-A |
| UKV | United Kingdom | PAL-A |
| EEC | European Economic Community | PAL-B |
| ESP | Spain | PAL-B |
| FRA | France | PAL-B |
| FRG | Federal Republic of Germany | PAL-B |
| GPS | Multiple countries (English box with local-language sticker and manual) | PAL-B |
| HOL | Holland (Netherlands) | PAL-B |
| KOR | Korea (Hyundai Comboy) | PAL-B |
| NOE | Nintendo of Europe | PAL-B |
| SCN | Scandinavia (Denmark, Norway, Sweden, Finland, Iceland) | PAL-B |
| SWE | Sweden | PAL-B |
| ASI | Asia | Asia |
| HKG | Hong Kong | Asia |
- Codes that appear only on boxes and manuals (CIC region not known to the wiki): GRE (Greece), ISR (Israel).
- Codes that appear only on back labels, usually for languages: ASD (logo of Audio Sound Distribution, distributor of early French releases, later merged into or replaced by Bandai), DAS (German and Spanish), EAI (England, Australia/Oceania, Italy), FAH (French and Dutch).
- Officially rebranded regional variants (console CICs still to be verified): Playtronic (Brazil), NTSC, with the PAL-M video conversion on an extra board; Samurai (India), Asia.
Disabling and defeating
Disabling the CIC is a popular modification that lets out-of-region games boot on a front-loader, though compatibility is not guaranteed. It is especially useful on PAL units, because of the A/B region split.
- Two-wire method: hold the CIC in reset and let the console’s reset button drive the CPU and PPU /RESET directly. Connect the lock CIC’s pin 7 (CIC RESET in) to pin 1 of the 74HCU04 inverter (oscillator), and the inverter’s pin 2 to the lock CIC’s pin 9 (CPU and PPU /RESET in). It is reversible.
- Pin 4 method: when the two CICs disagree only the lock, never the key, asserts its reset output. Set up as a key, the console CIC cannot reset the console. Disconnect its pin 4 from the board. The pin can optionally be tied to ground, but internal pull-downs make it read 0 when left floating.
- Defeating: boards by Camerica, Color Dreams, AVE and AGCI, and older Famicom-to-NES adapters, contain a charge pump that makes waveforms with -5 V, which freezes the CIC. Later front-loaders have diodes to protect the CIC data pins from out-of-range voltages, but not the reset pins. In late 2006 Tengen’s “Rabbit” chip was fully reverse-engineered and a PIC-based clone was made.
- A CIC “stun” circuit is patented (US 5,004,232); chips based on it were used in NINA-001 and NINA-002 boards (iNES 34).
Chip pinout and registers
The NES lockout chip is a 16-pin part (a primitive 4-bit microcontroller). Direction is as seen from the chip; “unused as input” and “unused as output” are the wiki’s own notes on pins whose port bit is not used that way.
| Pin | Port bit | Signal | Pin | Port bit | Signal |
|---|---|---|---|---|---|
| 1 | P0.0 | Data out (output) | 16 | Vcc | +5 V |
| 2 | P0.1 | Data in (input) | 15 | P2.2 | Gnd |
| 3 | P0.2 | Seed (input) | 14 | P2.1 | Gnd |
| 4 | P0.3 | Lock/Key (input) | 13 | P2.0 | Gnd |
| 5 | Xout | not connected | 12 | P1.3 | Gnd / reset speed B (input) |
| 6 | Xin | clock in | 11 | P1.2 | Gnd / reset speed A (input) |
| 7 | Rset | reset (input) | 10 | P1.1 | slave CIC reset (output) |
| 8 | Gnd | ground | 9 | P1.0 | /host reset (output) |
P0.x, P1.x and P2.x are I/O ports 0, 1 and 2; Xin and Xout are the clock pins. Registers: A is a 4-bit accumulator; C the carry flag; X a 4-bit general register; P a pointer used for memory access (PH its upper 2 bits, PL its lower 4 bits, used for I/O); IC the instruction counter, which counts in a polynomial rather than a linear way to save space; S the stack for IC; R 32 nibbles of RAM. The program ROM is 512 bytes (768 bytes in the 3195A).
Kevtris’ CIClone
An 8-pin replacement chip: 1 +5 V, 2 clock in, 3 “lockout functioning” (output), 4 data in, 5 reset, 6 data out, 7 /Force NTSC (input), 8 ground. Pin 3 goes high when the chip has completed 64 frames; it is only for debugging and not a reliable power-up reset (top-loaders lack the 4 MHz clock, so it floats or misbehaves there; cutting pin 4 of the lockout chip on a front-loader keeps it from ever going high). Pulling pin 7 low forces NTSC-only mode (3193 only); leaving it floating lets the chip try all four regions (the three PAL modes are not usable in forced mode).
krikzz’s ATtiny13 lockout chip
An AVR ATtiny13A on pins: 1 not connected, 2 clk in (NES pin 71), 3 led (output; low while the lockout works normally, high while the chip is trying to change region), 4 ground, 5 data out (NES pin 35), 6 data in (NES pin 34), 7 reset (NES pin 70), 8 VCC.
Sources
- NESdev Wiki: CIC lockout chip, which cites US patents 4,799,635 and 5,070,479 for how the CIC works
- NESdev Wiki: CIC lockout chip pinout
The NESdev Wiki text is available under CC BY-SA 3.0. This page is written in our own words from the raw wikitext kept in samples/nes/sources/hardware. Not covered: the chip’s internal program (the 10NES instruction listing and the key stream). The wiki pages fetched do not contain it. Requests for pages with plausible titles (10NES, Nintendo CIC, CIC pinout, CIC program listing, Lockout chip and more) returned “not found”, and a search of the wiki for “10NES” (saved as samples/nes/sources/hardware/Search_10NES.html, 2026-11-19) lists only the Glossary page; the only CIC pages on the wiki are the two written here. So it is left undescribed on this site; the patents above and the reverse-engineered clones are where it is documented.